SlotCarChitChat.com » 1410

1410 Atlas HO Motoring TV & Radio Tower Slot Car Racing Structure Box Lid

Administrator — Thu, 01 Apr 2010 10:45:47 +0000

The overall dimensions of this box is 7.5 inches wide by 5.5 inch tall by 2.0 inches deep.

Atlas HO Motoring TV Radio Tower Slot Car Racing Structure 1410-98

1410 Atlas HO Slot Car Racing Track Layout TV & Radio Tower Structure Left

Administrator — Sun, 21 Mar 2010 06:02:46 +0000

1410 Atlas HO Slot Car Racing Track Layout TV & Radio Tower Structure Left

1410 Atlas HO Slot Car Racing Track Layout TV & Radio Tower Structure Rear

Administrator — Sun, 21 Mar 2010 06:01:06 +0000

1410 Atlas HO Slot Car Racing Track Layout TV & Radio Tower Structure Rear

1410 Atlas HO Slot Car Racing Track Layout TV & Radio Tower Structure Right

Administrator — Sun, 21 Mar 2010 05:59:39 +0000

1410 Atlas HO Slot Car Racing Track Layout TV & Radio Tower Structure Right

1410 Atlas HO Slot Car Racing Track Layout TV & Radio Tower Structure

Administrator — Sat, 20 Mar 2010 14:37:50 +0000

Your atlas model 1410 tv & radio tower should be erected beside one of the turns on your track or, if your track is fairly elaborate, at some difficult to negotiate location where the action usually stays exciting. You’ll be able to keep your TV and radio personnel at their posts by means of a false sense of security if you stack a substantial pile of atlas hay bales between the track and the tower. Otherwise everyone aboard the tower is apt to join the birds each time one of the cars loses its grip and comes sliding in at it.

1410 Atlas HO Slot Car Racing Track Layout TV & Radio Tower Structure

Atlas HO Model 1410-98 TV & Radio Tower Assembly Instructions

Administrator — Wed, 03 Mar 2010 12:48:56 +0000

Install the four tubular columns 1 on base 2 by pressing each of the columns into one of the base lugs.
Line up the holes in one of the platforms 3 with the tops of the columns then carefully slide the platform downwardly until it is about 3/8 inch above the base.
Install the two remaining platforms on the columns leaving the uppermost platform flush with the column upper ends. Adjust the center platform along the columns to a position midway between the upper and lower platforms. If you wish the platforms may now be permanently fixed to the columns with a small dab of model airplane cement on the platform under-surfaces.
Determine the correct length for the ladder 4 by installing it temporarily. After marking the length remove the ladder and carefully cut off the excess. The ladder may now be cemented into the base and against the top rail of each platform.
Install TV camera 5 and cameraman 6 on the uppermost platform, the microphone 7 and announcer 8 on the center platform. Cement a small piece of paper over the opening on the rear of the TV monitor 9 then install it and the director 10 on the lower platform.

Atlas HO Slot Car Racing Track Layout Scenery 1410 TV & Radio Tower Assembly Instructions

HO Scale Slot Car Structures Box End Panel Graphics

Administrator — Wed, 17 Feb 2010 12:25:46 +0000

Part of the allure to collecting vintage Atlas buildings is the colorful graphics that each box displays. If you are investing in a complete set of these HO 1/87 scaled structures for your slot car layout you get an added value bonus of looking at a box with colorful artwork & graphics. Listed here again is all of the vintage HO motoring & racing plastic model scenery kits which were produced along with their original stock numbers and price.

1402-129 Grandstand
1403-98 Bleacher Stand
1404-89 Entrance Building
1405-89 Rest Room
1406-89 First Aid Station
1407-98 Refreshment Stand
1408-129 Pit Stop
1409-129 Official’s Stand
1410-98 TV & Radio Tower

Colorful box artwork is typical for the period and Atlas made no exception as you can see from this image of the side panels.

Atlas HO Slot Car Racing Plastic Model Building Kit Box End Panel Graphics